View Full Version : wheel spacers (ae86)
I need a set of spacers for my cam not to sure what size i need i think 25-30mil.
Does anyone know were i can get them?
Thanks
I need to fill this gap
http://i32.servimg.com/u/f32/14/72/95/66/img00330.jpg
bubble1984
01-08-10, 01:38
emmmm,
i tink u neeed 70-100mm spacers.
alternatively get good offset wheels or take off d arches, spacers. . . . dont tink so.
dude go on the hunt for some wide wheels... :cool:
sorry i off topic ere but was this parked in white water last nite about 9pm ????
would the stud pattern be the same as a 180 if so i have 30mm bolt on
no think its 4x100?
you need wide wheels, low offset to fill that gap
Daraghs14a
01-08-10, 13:00
Yeah i think they the same as 180 4x114.
Threads might be different on the nuts doh,
No Bart it was not mine.
ye i think they are 4x100.
i dont want to get new wheels i dont have money at the moment for them :(
AE86 is 4x114.3 same as the one 180's,cefiro's,integra's,and prob more i just cant think,might narrow down your search!!
AE86 is 4x114.3 same as the one 180's,cefiro's,integra's,and prob more i just cant think,might narrow down your search!!
didnt know that. Thanks for the help.
pretty sure carpo had a nice set of ssr mesh in 14's?
dont think anyone mentioned it, but I'm looking at buying 50mm spacers on driftworks.. nice bolt on jobbies, to suit 4/5 studs.
bout 110pounds posted, for 2.
worth a look if your stuck...
any wider any the inner arches will have to be cut on the back, bit of a headache, used to be mine!:)
any wider any the inner arches will have to be cut on the back, bit of a headache, used to be mine!:)so the cby's are just bolted on over the original arches??
so the cby's are just bolted on over the original arches??
ye the original arches are under the cby's
ye the original arches are under the cby's
you will have bother there so,they would need work when the wheels are spaced out your original arches is probly gonna be over the center off your tyre,that will cause you problems!!
you will have bother there so,they would need work when the wheels are spaced out your original arches is probly gonna be over the center off your tyre,that will cause you problems!!
there is loads of room between the arches and wheels. they wont touch off each other.
didnt realise you were'nt cutting arches, I am..
as the lads said, bigger offset of wheels, or even some
small 20mm spacers just bring them out, small spacers
like that don't need to be savage quality..
id now try donedeal for a wide drift car getting broke and
send a text dude, worth a shot.
Tekno Twinky
02-08-10, 23:42
didnt realise you were'nt cutting arches, I am..
as the lads said, bigger offset of wheels, or even some
small 20mm spacers just bring them out, small spacers
like that don't need to be savage quality..
id now try donedeal for a wide drift car getting broke and
send a text dude, worth a shot.
SMALL 20mm spacers!? thats an inch giles ha for that size you need bolt on spacers that are hub centric to ae86 which is like 61mm
AE86 - 4x114.3 with thread pitch of m12x1.5
180/S13 4 stud - 4x114.3 with thread pitch of m12x1.25
so spacer will fit on but you wont be able to bolt it thus its useless
10mm shim(non-bolted) spacer is the max w/o hub centric i think as iv had mishaps!
Options starting at the cheapest..
Pull them off and fill the holes as the original body is un-cut (i gather?).
2.- buy stupid big gay spacers circa 170-250e new,less 2nd hand.
3, buy mega negative offset 9j 15's from japan.
4,buy mega above in a 14"andcomplete the 1st option
5 i spotted these...http://www.ae86irl.com/forum/showthread.php?t=19833&highlight=wide+mesh
If i were you id genuinely pull them CBY arches off a fill the litlle rivet holes.
the offset is high-ish but they can be reversed then refurb'd weld the original valve hole, drill a new on the new side then balance then and wayhay! your away!
But if you havent the money
like i said just throw some small spacers, or get some off a drift car.
I'm eye'ing up m2tuning at the minute, driftworks haven't got my size.
killian he just wants to the step the wheels out abit.
Keep your arches, and your wheels, you obviously want them!
Oh and I must be wrong about the spacer size, maybe I'm thinking evo or something else..
5 i spotted these...http://www.ae86irl.com/forum/showthread.php?t=19833&highlight=wide+mesh
But if you havent the money
these feckers havent accepted my registration yet, i registered few days ago!
these feckers havent accepted my registration yet, i registered few days ago!
Im the same man, tried 8 times!
Getting a friend to try help me register!
Its only a car forum, I just want a few parts and abit of advice..
Its easier to open a bank account man..
Anyone have any spacers ?? please
i have a set here, no bolts though, i think they are 40-50mm, ill have a look and get back to you
i have four 25mm bolt ons. ready to rock. 160euro
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.